Prescriptions EN

ork made of wooden planks for construction of the bracing ring. Afterwards fill the formwork with reinforcement and concrete.Scaffolding used after finishing the 1st height8. QUALITY, CONTROL AND TESTING:Control input:- Visual inspection of the material, good storage, quantity and quality- Control design fundamentals - performs builder- Control of workplace readiness and machines.Check-process:- Control by waterproofing and possibly its damage and cleanliness.- Check correctness of the identification and establishment of masonry at the corners, it must be registered in the site diary.- Quality control performance mortar, right consistency and proportion of ingredients.- Inspection of verticality and horizontality of layers, use a plumb line and spirit level.- We check adequate filling of vertical and horizontal mortar joints - 12 mmControl output:- Masonry is carried out in accordance with current standards. The design of masonry structures will personally oversee construction manager or an appointed master. Will personally monitor technological progress and accurate positioning.- Accuracy of load-bearing walls: 2mm to project the shape when measuring two meters battens.- Technical supervision (TDI) will oversee the technological processes and the quality of work performed. Everything will be recorded in the construction log.9. HEALTH AND SAFETY:will be respected in the implementation of particular- Government Regulation No. 591/2006Sb. The detailed minimum requirements for health and safety at work sites)- Nař.vlády č.362/2005Sb., The detailed requirements for safety and health at workplaces with the danger of falling from heights or into hloubky.7- Council Directive 92/57/EEC on the minimum safety and health requirements at temporary or transitional sites- Act č.61/1988Sb. The mining activities, explosives and state mining administration- Government Regulation č.101/2005Sb., Podr.pož.na the workplace and working environment- Vyhl.č.137/1998Sb. The general technical requirements for construction- Government Regulation č.178/2001Sb. Laying down the conditions of health of workers at work, as amended by Government č.523/2002Sb.a nař.vl.č.441/2004nař.vl.č.378/2001Sb. laying down detailed requirements for safe operation and use of machinery, technical equipment, appliances and toolsOperators of machinery and electrical equipment:- The shear, thrust and other dangerous places machines that would threaten the workers had remained freely accessible, must be designed to prevent access or must be used protective equipment.- Machines with rotating tools must be secured against self-loosening tools.- The machine may only work for people with the necessary skills.- All the fast moving machine parts (shafts, pulleys, sprockets, etc.) Must be properly secured hard covers.- Lubrication, cleaning and repair of machines for running is strictly prohibited.- Using the machine near the power lines. Self-propelled machines and equipment, the external dimension of the transport does not change, can be used at work (travel) under power lines and close only if they comply with the prescribed safety distances machinery or equipment and workers from power lines.- Excavators, loaders, hydraulic arms, etc. must be placed so that at any position all parts outside the protection zone el. lines, unless otherwise provided safety (off line, signaling worker, etc.)..- When moving the machine must always be disconnected from the power, energy. Just not enough to trip the circuit breaker.- Electrical equipment that threaten the life or health of persons must be immediately disconnected and secured.- Distribution of electricity must be securely protected against mechanical damage and against the adverse effects of moisture.- The main switch must be permanently accessible and clearly marked.- Repair of electrical wiring must be performed only by qualified and designated person.- Keep under a suspended load is strictly prohibited.- Tying the load to the lifting device may only qualified binder.10. ECOLOGY:When performing vertical structures is needed to minimize the impact on the environment. It is all about dust, noise and pollution communications. Used machinery, must be in good repair, so that did not bother the neighborhood by excessive noise, the construction must be followed for the implementation of timeouts noisy work. Dirty cars and other machinery must be before leaving the building cleaned. Alternatively, should be cleaned communications. Mechanization should be weaned on paved surfaces.Waste management:Act No. 185/2001 s.b. WasteThe Ministry of Environment No. 381/2001 Coll Waste and their list. In addition, these wastes in the largest quantities sort by your material.11. LITERATURE:Support - technology works 1 Module 1,2,3I. Technology of buildings, Coachman et al.Government Regulation No. 591/2006 s.b.Government Regulation No. 362/2005 s.b.Act No. 185/2001 s.b.The Ministry of Environment No. 381/2001 CollWebsiteCatalogs construction machinery
TECHNOLOGICAL PRESCRIPTION For ROOF1. GENERAL INFORMATIONPURPOSE: FAMILY HOUSELOCATION:HORNÉ PASEKY 223, Č.P. 13/2, 902 95INVESTOR: RÓBERT BURIANOWNER: RÓBERT BURIANDESIGNER: PAVEL SUBALLYDEVELOPER: PALYSTAV a.s. : ESTÓNSKA 13, 113 10, LIDOČKO IČ:199 22 05 DIČ: SK 710 15 091.1. GENERAL INFORMATIONIt is a new two story detached house with a gable roof. Monolithic reinforced concrete foundations will be, made belts. Supporting structures are walled ceramic bricks ended 30 HELUZ ring. Ceilings are made
TECHNOLOGICAL PRESCRIPTIONFor SLABS1. GENERAL INFORMATION ABOUT THE PROJECTPURPOSE: FAMILLY HOUSELOCATION: HORNÉ PASEKY 223, Č.P. 13/2, 902 95INVESTOR: RÓBERT BURIANOWNER: RÓBERT BURIANDESIGNER: PAVEL SUBALLYIMPLEMENTATION: PALYSTAV a.s.ESTÓNSKA 13, 113 10, LIDOČKO IČ:199 22 05 DIČ: SK 710 15 091.1. GENERAL INFORMATION ABOUT CONSTRUCTIONIt is a new two story detached house with a gable roof. Monolithic reinforced concrete foundations will be, made belts. Supporting structures are walled ceramic bricks ended 30 HELUZ ring. Ceilings are made